tatus 0501, change 0000, 480 Mb/s
[  343.350463] usb 1-1: new high speed USB device using musb_hdrc and address 34
[  343.474884] usb 1-1: device descriptor read/64, error -71
[  348.584381] usb 1-1: khubd timed out on ep0in len=0/64
[  350.063049] twl4030_usb twl4030_usb: HW_CONDITIONS 0x50/80; link 1
[  353.584259] usb 1-1: khubd timed out on ep0in len=0/64
[  358.584442] usb 1-1: khubd timed out on ep0in len=0/64
[  358.709442] usb 1-1: device descriptor read/64, error -110
[  358.943664] usb 1-1: new high speed USB device using musb_hdrc and address 35
[  363.943786] usb 1-1: khubd timed out on ep0in len=0/64
[  364.068756] usb 1-1: device descriptor read/64, error -19
[  364.303131] usb 1-1: device descriptor read/64, error -19
[  364.475036] hub 1-0:1.0: port 1 not reset yet, waiting 50ms
[  364.537506] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  364.748352] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  364.959381] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  364.959411] hub 1-0:1.0: port_wait_reset: err = -16
[  364.959442] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  365.170318] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  365.381225] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  365.592224] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  365.592254] hub 1-0:1.0: port_wait_reset: err = -16
[  365.592285] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  365.803131] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  366.013946] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  366.225128] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  366.225158] hub 1-0:1.0: port_wait_reset: err = -16
[  366.225158] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  366.435852] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  366.646789] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  366.857788] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  366.857849] hub 1-0:1.0: port_wait_reset: err = -16
[  366.857879] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  367.068664] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  367.279632] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  367.490692] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  367.490753] hub 1-0:1.0: port_wait_reset: err = -16
[  367.490783] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  367.490814] hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
[  367.553100] hub 1-0:1.0: port 1 not reset yet, waiting 50ms
[  367.615631] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  367.826477] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  368.037536] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  368.037567] hub 1-0:1.0: port_wait_reset: err = -16
[  368.037597] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  368.248443] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  368.459442] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  368.670379] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  368.670410] hub 1-0:1.0: port_wait_reset: err = -16
[  368.670440] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  368.881256] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  369.092193] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  369.303131] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  369.303161] hub 1-0:1.0: port_wait_reset: err = -16
[  369.303192] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  369.514068] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  369.724884] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  369.936004] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  369.936035] hub 1-0:1.0: port_wait_reset: err = -16
[  369.936065] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  370.146881] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  370.357818] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  370.568664] hub 1-0:1.0: port 1 not reset yet, waiting 200ms
[  370.568695] hub 1-0:1.0: port_wait_reset: err = -16
[  370.568725] hub 1-0:1.0: port 1 not enabled, trying reset again...
[  370.568756] hub 1-0:1.0: Cannot enable port 1.  Maybe the USB cable is bad?
[  370.568847] hub 1-0:1.0: unable to enumerate USB device on port 1
[  370.568908] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[  370.568969] hub 1-0:1.0: port 1 enable change, status 00000501
[  373.232727] hub 1-0:1.0: hub_suspend
[  373.232788] usb usb1: bus auto-suspend
[  402.170318] musb_h_ep0_irq 1083: no URB for end 0
[  422.693298] twl4030_usb twl4030_usb: HW_CONDITIONS 0xd0/208; link 2
[  460.627044] usb usb1: usb resume
[  460.646667] hub 1-0:1.0: hub_resume
[  460.646728] hub 1-0:1.0: port 1: status 0101 change 0001
[  460.756256] hub 1-0:1.0: state 7 ports 1 chg 0002 evt 0000
[  460.756347] hub 1-0:1.0: port 1, status 0101, change 0000, 12 Mb/s
[  460.881164] usb 1-1: new high speed USB device using musb_hdrc and address 38
[  461.031707] usb 1-1: default language 0x0409
[  461.032897] usb 1-1: uevent
[  461.033111] usb 1-1: usb_probe_device
[  461.033142] usb 1-1: configuration #1 chosen from 1 choice
[  461.036560] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[  461.036926] usb 1-1:1.0: uevent
[  461.037109] hub 1-1:1.0: usb_probe_interface
[  461.037139] hub 1-1:1.0: usb_probe_interface - got id
[  461.037170] hub 1-1:1.0: USB hub found
[  461.037689] hub 1-1:1.0: 4 ports detected
[  461.037719] hub 1-1:1.0: standalone hub
[  461.037750] hub 1-1:1.0: ganged power switching
[  461.037780] hub 1-1:1.0: global over-current protection
[  461.037780] hub 1-1:1.0: Single TT
[  461.037811] hub 1-1:1.0: TT requires at most 32 FS bit times (2664 ns)
[  461.037841] hub 1-1:1.0: Port indicators are supported
[  461.037872] hub 1-1:1.0: power on to power good time: 100ms
[  461.038513] hub 1-1:1.0: local power source is good
[  461.038574] hub 1-1:1.0: no over-current condition exists
[  461.038604] hub 1-1:1.0: enabling power on all ports
[  461.041320] drivers/usb/core/inode.c: creating file '038'
[  461.041992] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608
[  461.042022] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  461.042053] usb 1-1: Product: USB2.0 Hub
[  461.042114] hub 1-0:1.0: state 7 ports 1 chg 0000 evt 0002
[  461.042175] hub 1-0:1.0: port 1 enable change, status 00000503
[  461.139282] hub 1-1:1.0: port 1: status 0101 change 0001
[  461.140258] hub 1-1:1.0: port 2: status 0301 change 0001
[  461.140869] hub 1-1:1.0: port 3: status 0101 change 0001
[  461.240509] hub 1-1:1.0: state 7 ports 4 chg 000e evt 0000
[  461.240905] hub 1-1:1.0: port 1, status 0101, change 0000, 12 Mb/s
[  461.327026] usb 1-1.1: new high speed USB device using musb_hdrc and address 39
[  461.437438] usb 1-1.1: default language 0x0409
[  461.438323] usb 1-1.1: uevent
[  461.438446] usb 1-1.1: usb_probe_device
[  461.438476] usb 1-1.1: configuration #1 chosen from 1 choice
[  461.439819] usb 1-1.1: adding 1-1.1:1.0 (config #1, interface 0)
[  461.440032] usb 1-1.1:1.0: uevent
[  461.440155] hub 1-1.1:1.0: usb_probe_interface
[  461.440155] hub 1-1.1:1.0: usb_probe_interface - got id
[  461.440185] hub 1-1.1:1.0: USB hub found
[  461.441528] hub 1-1.1:1.0: 4 ports detected
[  461.441558] hub 1-1.1:1.0: standalone hub
[  461.441589] hub 1-1.1:1.0: ganged power switching
[  461.441589] hub 1-1.1:1.0: global over-current protection
[  461.441619] hub 1-1.1:1.0: Single TT
[  461.441619] hub 1-1.1:1.0: TT requires at most 32 FS bit times (2664 ns)
[  461.441650] hub 1-1.1:1.0: Port indicators are supported
[  461.441650] hub 1-1.1:1.0: power on to power good time: 100ms
[  461.444030] hub 1-1.1:1.0: local power source is good
[  461.444061] hub 1-1.1:1.0: no over-current condition exists
[  461.444061] hub 1-1.1:1.0: enabling power on all ports
[  461.445770] drivers/usb/core/inode.c: creating file '039'
[  461.446166] usb 1-1.1: New USB device found, idVendor=05e3, idProduct=0608
[  461.446197] usb 1-1.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[  461.446197] usb 1-1.1: Product: USB2.0 Hub
[  461.448333] hub 1-1:1.0: port 2, status 0301, change 0000, 1.5 Mb/s
[  461.530395] usb 1-1.2: new low speed USB device using musb_hdrc and address 40
[  461.545654] hub 1-1.1:1.0: port 1: status 0101 change 0001
[  461.546997] hub 1-1.1:1.0: port 4: status 0101 change 0001
[  461.641326] usb 1-1.2: skipped 1 descriptor after interface
[  461.641906] usb 1-1.2: default language 0x0409
[  461.644256] usb 1-1.2: uevent
[  461.644500] usb 1-1.2: usb_probe_device
[  461.644531] usb 1-1.2: configuration #1 chosen from 1 choice
[  461.650268] usb 1-1.2: adding 1-1.2:1.0 (config #1, interface 0)
[  461.650695] usb 1-1.2:1.0: uevent
[  461.651550] drivers/usb/core/inode.c: creating file '040'
[  461.652221] usb 1-1.2: New USB device found, idVendor=046d, idProduct=c06c
[  461.652282] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[  461.652313] usb 1-1.2: Product: USB Optical Mouse
[  461.652343] usb 1-1.2: Manufacturer: Logitech
[  461.657928] hub 1-1:1.0: port 3, status 0101, change 0000, 12 Mb/s
[  461.740875] usb 1-1.3: new high speed USB device using musb_hdrc and address 41
[  461.912872] usb 1-1.3: default language 0x0409
[  461.913818] usb 1-1.3: uevent
[  461.913940] usb 1-1.3: usb_probe_device
[  461.913940] usb 1-1.3: configuration #1 chosen from 1 choice
[  461.916076] usb 1-1.3: adding 1-1.3:1.0 (config #1, interface 0)
[  461.916259] usb 1-1.3:1.0: uevent
[  461.916412] libusual 1-1.3:1.0: usb_probe_interface
[  461.916442] libusual 1-1.3:1.0: usb_probe_interface - got id
[  461.932647] drivers/usb/core/inode.c: creating file '041'
[  461.932983] usb 1-1.3: New USB device found, idVendor=059f, idProduct=1052
[  461.933013] usb 1-1.3: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[  461.933013] usb 1-1.3: Product: P'9220 Mobile Drive
[  461.933044] usb 1-1.3: Manufacturer: LaCie
[  461.933044] usb 1-1.3: SerialNumber: 00000000d40c2b8c30a2
[  461.933074] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0004
[  461.935729] hub 1-1.1:1.0: state 7 ports 4 chg 0012 evt 0000
[  461.936492] hub 1-1.1:1.0: port 1, status 0101, change 0000, 12 Mb/s
[  462.022003] usb 1-1.1.1: new high speed USB device using musb_hdrc and address 42
[  462.135223] Initializing USB Mass Storage driver...
[  462.135498] usb-storage 1-1.3:1.0: usb_probe_interface
[  462.135528] usb-storage 1-1.3:1.0: usb_probe_interface - got id
[  462.138946] usb 1-1.1.1: default language 0x0409
[  462.140777] scsi0 : SCSI emulation for USB Mass Storage devices
[  462.150421] usb 1-1.1.1: uevent
[  462.150543] usb 1-1.1.1: usb_probe_device
[  462.150573] usb 1-1.1.1: configuration #1 chosen from 1 choice
[  462.153747] usb 1-1.1.1: adding 1-1.1.1:1.0 (config #1, interface 0)
[  462.153930] usb 1-1.1.1:1.0: uevent
[  462.156250] drivers/usb/core/inode.c: creating file '042'
[  462.156616] usb 1-1.1.1: New USB device found, idVendor=05ac, idProduct=1402
[  462.156616] usb 1-1.1.1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  462.156646] usb 1-1.1.1: Product: Apple USB Ethernet Adapter
[  462.156646] usb 1-1.1.1: Manufacturer: Apple Inc.      
[  462.156677] usb 1-1.1.1: SerialNumber: 11075E
[  462.161437] hub 1-1.1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[  462.168731] usbcore: registered new interface driver usb-storage
[  462.169036] USB Mass Storage support registered.
[  462.180664] usb-storage: device found at 41
[  462.180664] usb-storage: waiting for device to settle before scanning
[  462.248535] usb 1-1.1.4: new high speed USB device using musb_hdrc and address 43
[  462.438629] usb 1-1.1.4: default language 0x0409
[  462.439910] usb 1-1.1.4: uevent
[  462.440063] usb 1-1.1.4: usb_probe_device
[  462.440063] usb 1-1.1.4: configuration #1 chosen from 1 choice
[  462.442260] usb 1-1.1.4: adding 1-1.1.4:1.0 (config #1, interface 0)
[  462.442443] usb 1-1.1.4:1.0: uevent
[  462.442565] libusual 1-1.1.4:1.0: usb_probe_interface
[  462.442596] libusual 1-1.1.4:1.0: usb_probe_interface - got id
[  462.442687] usb-storage 1-1.1.4:1.0: usb_probe_interface
[  462.442718] usb-storage 1-1.1.4:1.0: usb_probe_interface - got id
[  462.450836] usbhid 1-1.2:1.0: usb_probe_interface
[  462.450866] usbhid 1-1.2:1.0: usb_probe_interface - got id
[  462.462738] input: Logitech USB Optical Mouse as /class/input/input4
[  462.515197] scsi1 : SCSI emulation for USB Mass Storage devices
[  462.529174] drivers/usb/core/inode.c: creating file '043'
[  462.529602] usb 1-1.1.4: New USB device found, idVendor=0718, idProduct=0703
[  462.529632] usb 1-1.1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[  462.529632] usb 1-1.1.4: Product: TF090 Drive
[  462.529663] usb 1-1.1.4: Manufacturer: TDKMedia
[  462.529663] usb 1-1.1.4: SerialNumber: AAGLTJ2TSDJOAXH1
[  462.534332] usb-storage: device found at 43
[  462.534332] usb-storage: waiting for device to settle before scanning
[  462.570343] generic-usb 0003:046D:C06C.0001: input: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-musb_hdrc-1.2/input0
[  462.573822] usbcore: registered new interface driver usbhid
[  462.573883] usbhid: v2.6:USB HID core driver
[  462.751525] asix 1-1.1.1:1.0: usb_probe_interface
[  462.751556] asix 1-1.1.1:1.0: usb_probe_interface - got id
[  463.602081] eth0: register 'asix' at usb-musb_hdrc-1.1.1, ASIX AX88772 USB 2.0 Ethernet, 40:3c:fc:00:3d:96
[  463.605560] usbcore: registered new interface driver asix
[  467.179626] usb-storage: device scan complete
[  467.181060] scsi 0:0:0:0: Direct-Access     SAMSUNG  HM500JI          2AC1 PQ: 0 ANSI: 5
[  467.198669] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[  467.199310] sd 0:0:0:0: [sda] Write Protect is off
[  467.199340] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[  467.199371] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  467.200622] sd 0:0:0:0: [sda] 976773168 512-byte hardware sectors: (500 GB/465 GiB)
[  467.201202] sd 0:0:0:0: [sda] Write Protect is off
[  467.201263] sd 0:0:0:0: [sda] Mode Sense: 23 00 00 00
[  467.201385] sd 0:0:0:0: [sda] Assuming drive cache: write through
[  467.201446]  sda:<7>usb-storage: device scan complete
[  467.954559] scsi 1:0:0:0: Direct-Access     TDKMedia TF090 Drive      1100 PQ: 0 ANSI: 0 CCS
[  469.072357]  sda1 sda2 sda3
[  469.092864] sd 0:0:0:0: [sda] Attached SCSI disk
[  469.117034] sd 1:0:0:0: [sdb] 15722496 512-byte hardware sectors: (8.04 GB/7.49 GiB)
[  469.117828] sd 1:0:0:0: [sdb] Write Protect is off
[  469.117889] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[  469.117919] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[  469.125457] sd 1:0:0:0: [sdb] 15722496 512-byte hardware sectors: (8.04 GB/7.49 GiB)
[  469.126312] sd 1:0:0:0: [sdb] Write Protect is off
[  469.126373] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[  469.126403] sd 1:0:0:0: [sdb] Assuming drive cache: write through
[  469.126434]  sdb: sdb1
[  469.136810] sd 1:0:0:0: [sdb] Attached SCSI removable disk
[  487.645263] NTFS driver 2.1.29 [Flags: R/O MODULE].
[  487.744445] NTFS-fs warning (device sda1): parse_options(): Option utf8 is no longer supported, using option nls=utf8. Please use option nls=utf8 in the future and make sure utf8 is compiled either as a module or into the kernel.
[  487.822082] NTFS volume version 3.1.
[  488.326202] NTFS-fs warning (device sda2): parse_options(): Option utf8 is no longer supported, using option nls=utf8. Please use option nls=utf8 in the future and make sure utf8 is compiled either as a module or into the kernel.
[  488.361297] NTFS volume version 3.1.